Track Bandwidth On Linux Using vnStat

vnStat is a comprehensive package for Linux operating systems used to track and monitor bandwidth usage. It is included in the default repositories of most package managers.

This tutorial will teach you how to install, configure, and view the output from vnStat.


vnStat has packages in most popular package managers. Use the snippet below relevant for your system, or compile the program from its source code.


$ apt-get install vnstat


$ yum install vnstat

Compiling from source

Grab the latest version of vnStat from the official site.

$ wget

Once the file has downloaded, extract it and execute the following commands.

$ tar -xvf vnstat-1.13.tar.gz$ cd vnstat-1.13/$ make

Once this completes, install it using the command below.

$ make install

Configuration for yum/manual installs

Skip this section if you installed vnStat using apt-get.

If you installed directly from source or using yum, you will have to specify the adapter(s) that you want monitored. This is all configured automatically when installed using apt-get.

Run the following command to view all available interfaces that vnStat can monitor.

$ vnstat --iflist

To log traffic for the default interface on yum/manual installations, execute the following command. This also creates the database for the adapter.

$ vnstat -u -i eth0

Next, start the vnStat daemon using the command:

$ vnstatd -d 

You can also add this command to your /etc/rc.local file, so that it starts automatically when your system boots.

Configuring vnStat options

You can edit the vnStat config file located at /etc/vnstat.conf to customize the options to your preference. Use a text editor to open and edit the file.

$ nano /etc/vnstat.conf

If you prefer bandwidth stats to be output in KB/MB/GB/TB format instead of the default KiB/MiB/GiB/TiB format, change UnitMode 0 to UnitMode 1, and you may also change RateUnit 1 to RateUnit 0 to display the rates in bytes.

You should also change the maximum bandwidth to that of the port on your VPS (1 GiB or 10 GiB). Change MaxBandwidth 100 to MaxBandwidth 1000 (for 1GiB port) or MaxBandwidth 10000 (for 10GiB port)

Track Bandwidth On Linux Using vnStat

Save and exit the file.


To see a quick summary of the traffic consumed, use the bare command vnstat.

root@vultr:~# vnstatDatabase updated: Sun Dec 13 04:56:02 2015   eth0 since 12/13/2015          rx:  225 KB      tx:  229 KB      total:  454 KB   monthly                     rx      |     tx      |    total    |   avg. rate     ------------------------+-------------+-------------+---------------       Dec '15        225 KB |      229 KB |      454 KB |      0.00 KB/s     ------------------------+-------------+-------------+---------------     estimated        --     |      --     |      --     |   daily                     rx      |     tx      |    total    |   avg. rate     ------------------------+-------------+-------------+---------------         today        225 KB |      229 KB |      454 KB |      0.03 KB/s     ------------------------+-------------+-------------+---------------     estimated        --     |      --     |      --     |

To get more specific data, you can use the vnstat -m and vnstat -d commands for month and day level output, respectively.

root@vultr:~# vnstat -m eth0  /  monthly       month        rx      |     tx      |    total    |   avg. rate    ------------------------+-------------+-------------+---------------      Dec '15        225 KB |      229 KB |      454 KB |      0.00 KB/s    ------------------------+-------------+-------------+---------------    estimated        --     |      --     |      --     |root@vultr:~# vnstat -d eth0  /  daily         day         rx      |     tx      |    total    |   avg. rate     ------------------------+-------------+-------------+---------------     12/13/2015       225 KB |      229 KB |      454 KB |      0.03 KB/s     ------------------------+-------------+-------------+---------------     estimated        --     |      --     |      --     |

You can also display live traffic statistics using the command vnstat -l.

root@vultr:~# vnstat -lMonitoring eth0...    (press CTRL-C to stop)   rx:       0.03 KB/s     0 p/s          tx:       0.19 KB/s     0 p/s

Want to contribute?

You could earn up to $300 by adding new articles

Submit your article
Suggest an update
Request an article

No comments

Powered by Blogger.